標題: SC5w Mk II AA Flashlight Neutral White [打印本頁] 作者: X-Ray 時間: 2017-4-19 10:32 標題: SC5w Mk II AA Flashlight Neutral White
Zebralight 推出新的 Sc5w Mk II
使用 AA 電池，預計五月推出。
Cree XP-L2 EasyWhite LED
Nominal CCT 4500K
Typical CRI: 83-85
Tint deviation: 3-Step MacAdam ellipse
User Selectable Levels: 3 main levels (High, Medium and Low). Each main level can be programmed to one of its two sub-levels. The second sub-level of the each main levels can be further programmed to different brightness levels.
Light Output (runtimes)
High: H1 550 Lm (3min, then 407lm, total min) or H2 407 Lm ( hr) / 274 Lm ( hrs) / 166 Lm ( hrs)
Medium: M1 92 Lm ( hrs) or M2 46 Lm ( hrs) / 21 Lm ( hrs) / 8.6 Lm ( hrs)
Low: L1 3.2 Lm ( days) or L2 1.1 Lm ( days) / 0.33 Lm ( days) / 0.09 Lm ( months)
Beacon Strobe Mode: 4Hz Strobe at H1 / 19Hz Strobe at H1
Light output are ANSI out the front (OTF) values. Runtimes tested (and parasitic drain estimated) using Panasonic Eneloop Pro AA batteries. Remaining battery power, about 10-20%, after step-down are not counted towards the runtimes.
Operating Voltage Range: 0.7V - 2.0V
Battery: One AA size NiMH, lithium or alkaline battery. Panasonic Eneloop or Eneloop Pro is highly recommended. Batteries are not included in the box.
Parasitic Drain: 2.4 uA (much less than the self discharging of a battery)
Beam Type
80 degree spill
10 degree hot spot
Dimensions
Head Diameter: 1.0 inch (25.4 mm)
Length: 3.2 inch (80.3 mm)
Weight
1.8 oz (49 gram)
Multiple Mode Groups
This light comes with three mode groups, G5, G6 and G7. The G5, set as the factory default, can be selected with 5-click from OFF, while G6 and G7 can be selected with 6-click and 7-click from OFF respectively. Mode group selections are memorized after the light is turned off and through battery changes.
In all three mode groups
H can be either H1 or H2; M can be either M1 or M2; L can be either L1 or L2
from OFF: 1-click to H; 2-click to M; press and hold to cycle from L, M to H
In G5
H1 is fixed at 550Lm, H2 can be 407, 274, or 166Lm
M1 is fixed at 92Lm, M2 can be 46, 21, or 8.6Lm
L1 is fixed at 3.2Lm, L2 can be 1.1, 0.33 or 0.09Lm
In G6 and G7
H1, H2, M1, M2, L1 and L2 can be programmed to any of the 12 available brightness levels
Double-click 6 times at the H1, H2, ... L2 to enter the programming mode for that level. Once in the programming mode, use double-click to go up one level and triple-click to go down one level. Use 1-click to exit the programming mode
Three consecutive 5-click (or 6-click, 7-click) to reset the G5 (or G6, G7) back to the factory default settings
圖片附件: sc5iimain.jpg (2017-4-19 10:32, 19.84 KB) / 下載次數 328
