Cree XP-L2 EasyWhite LED
Nominal CCT 4000K
Typical CRI: 93-95
Tint deviation: 2-step
User Selectable Levels: 3 main levels (High, Medium and Low). Each main level can be programmed to one of its two sub-levels. The second sub-level of the each main levels can be further programmed to different brightness levels.
Light Output (runtimes)
High: H1 285 Lm (0.9 hr) or H2 238 Lm (1.6 hr) / 171 Lm (2.3 hrs) / 106 Lm (4.2 hrs)
Medium: M1 56 Lm (8.5 hrs) or M2 26 Lm (21 hrs) / 10.3 Lm (41 hrs) / 3.5 Lm (4.5 days)
Low: L1 1.0 Lm (13 days) or L2 0.26 Lm (1.1 month) / 0.06 Lm (2.2 months) / 0.01 Lm (3.3 months)
Beacon Strobe Mode: 0.2Hz Beacon at Low / 0.2Hz Beacon at H1 / 4Hz Strobe at H1 / 19Hz Strobe at H1
Light output are ANSI out the front (OTF) values. Runtimes tested (and parasitic drain estimated) using Panasonic Eneloop Pro AA batteries. Remaining battery power, about 10-20%, after step-down are not counted towards the runtimes.
Operating Voltage Range: 0.7V - 2.0V
Battery: One AA size NiMH, lithium or alkaline battery. Panasonic Eneloop or Eneloop Pro is highly recommended. Batteries are not included in the box.
Parasitic Drain: Negligible (much less than the self discharging of a battery)
Beam Type
80 degree spill
12 degree hot spot
Dimensions
Head Diameter: 0.96 inch (23.6 mm)
Length: 3 inch (77.6 mm)
Weight
1.4 oz (40 gram)
Features
Battery capacity indicator (LED flashes 1-4 times, 4 short clicks to start)
All levels are current regulated
Low battery alert when the light is switched OFF (LED flashes if the battery voltage is below ~1.06V)
Automatic stepping down from High to Medium, and from Medium to Low when battery capacity is low
Durable electronic soft-touch switch
Smart user interface provides fast and easy access to all brightness levels and beacon-strobes.
Precision machined unibody casing from premium grade aluminum bar stocks
Proprietary heat sinking design bonds the LED board directly to the unibody aluminum casing
Durable natural hard anodized finish (Type III Class I)
Sealed and potted LED driver circuitry
Tempered optical grade glass
Preinstalled optical grade glass
Orange peel reflector
Battery power can be disconnected by slightly unscrewing the tailcap to prevent unwanted activations or parasitic drain
Waterproof to IPX8 (2 meters, 30 minutes)
SC53w AA Neutral White Flashlight
Cree XP-L2 EasyWhite LED
Nominal CCT 4500K
Minimum CRI: 80
Tint deviation: 3-step
User Selectable Levels: 3 main levels (High, Medium and Low). Each main level can be programmed to one of its two sub-levels. The second sub-level of the each main levels can be further programmed to different brightness levels.
Light Output (runtimes)
High: H1 330 Lm (0.9 hr) or H2 275 Lm (1.6 hr) / 198 Lm (2.3 hrs) / 122 Lm (4.2 hrs)
Medium: M1 65 Lm (8.5 hrs) or M2 30 Lm (21 hrs) / 12 Lm (41 hrs) / 4.1 Lm (4.5 days)
Low: L1 1.2 Lm (13 days) or L2 0.31 Lm (1.1 month) / 0.07 Lm (2.2 months) / 0.013 Lm (3.3 months)
Beacon Strobe Mode: 0.2Hz Beacon at Low / 0.2Hz Beacon at H1 / 4Hz Strobe at H1 / 19Hz Strobe at H1
Light output are ANSI out the front (OTF) values. Runtimes tested (and parasitic drain estimated) using Panasonic Eneloop Pro AA batteries. Remaining battery power, about 10-20%, after step-down are not counted towards the runtimes.
Operating Voltage Range: 0.7V - 2.0V
Battery: One AA size NiMH, lithium or alkaline battery. Panasonic Eneloop or Eneloop Pro is highly recommended. Batteries are not included in the box.
Parasitic Drain: Negligible (much less than the self discharging of a battery)
Beam Type
80 degree spill
12 degree hot spot
Dimensions
Head Diameter: 0.96 inch (23.6 mm)
Length: 3 inch (77.6 mm)
Weight
1.4 oz (40 gram)
斑馬這一系列似乎差異不大,
除了更小的體積,略大的中心光斑(相對於SC5 MKII的10度,
使用較低的H1亮度來達到不會降檔的目的(H1 285 Lm 0.9 hr),
唯一比較特別的大概就是多了
Low battery alert when the light is switched OFF (LED flashes if the battery voltage is below ~1.06V)
當電池電壓低於1.06V時,關閉手電筒時LED會閃爍提示.
以及沒有電池物理防反接(不確定是沒有還是漏掉標示)作者: toobadorz 時間: 2017-7-21 20:45
圖片附件: 1.jpg (2017-7-21 11:21, 20.25 KB) / 下載次數 712
這......該怎麼說呢！ 雖然我喜歡SC53的外型